A grey card and a colour chart look like the same kind of accessory and do quite different jobs. One gives you a neutral reference for exposure and white balance. The other gives you a set of known colour values that let software work out how your camera rendered the scene, and match it to another camera. Shooting one reference frame at the head of a setup costs ten seconds and saves an hour in post.
Three tools, three jobs
- White balance card. A spectrally flat neutral surface, often white or light grey. Its only job is to be colour-neutral so the camera or the converter can remove a cast.
- 18 per cent grey card. A neutral of known reflectance, used to set exposure with a reflected meter. Also works for white balance.
- Colour reference chart. An array of patches with published, measured colour values, used to build camera profiles and to match cameras to each other.
You can white balance off a grey card, but you cannot build a camera profile from one, because a single neutral tells you nothing about how the sensor handles saturated colour.
Shooting the reference frame
The value of the reference depends entirely on shooting it correctly:
- Put the chart in the same light as the subject, at the subject position. A chart lit by a different source describes a scene you are not shooting.
- Fill enough of the frame that the patches are clean and readable: a third of the frame width is plenty. Filling the whole frame is unnecessary and often means moving the chart out of the subject light.
- Angle it to avoid specular reflection. A sheen across the patches destroys the reading. Tilt slightly away from the key.
- Expose it correctly. An under- or over-exposed chart gives the software wrong values to work from.
- Shoot one per lighting setup, not one per day. Any change to the lights means a new reference.
White balance from a neutral
Two routes. Setting a custom white balance in camera bakes the correction into the JPEG and tags the raw file; picking the neutral with an eyedropper in a raw converter afterwards achieves the same thing with more precision and no time cost on set.
If you shoot raw, the second is strictly better, because white balance in a raw file is a tag rather than an applied change: there is no penalty for fixing it later. If you shoot JPEG or record video with a baked profile, do it in camera.
The 18 per cent question
Grey cards are conventionally 18 per cent reflectance, which corresponds to middle grey perceptually. Camera meters, however, are calibrated to somewhere between 12 and 18 per cent depending on manufacturer, which is why metering off a grey card can leave you consistently a third to half a stop out on a given body.
This is not a reason to distrust the card. It is a reason to calibrate once: meter your card, shoot it, check where it lands on the histogram or waveform, and note the offset your camera needs. After that it is repeatable.
Where colour charts really earn their keep
Single-camera work with a good white balance rarely needs a full chart. Multi-camera work does, and this is the strongest argument for shooting one.
Two bodies from different manufacturers, or even two generations of the same manufacturer, render colour differently: particularly skin tones and saturated reds. Intercutting them without matching is visible. With a chart in the head of each camera’s take, grading software can compute a transform that brings both to a common reference, and the cut stops drawing attention to itself.
The same applies across time: a chart shot on day one lets you match a reshoot three weeks later under different conditions.
Building a camera profile
Beyond matching, a chart lets you generate a colour profile for your specific body under specific lighting. The software compares the measured patch values in your frame against the reference values and produces a correction. For product and reproduction work, where colour accuracy is the deliverable rather than a preference, this is the only defensible way to work.
Be aware that a profile built under tungsten does not apply under daylight, and that profiling optimises for accuracy rather than for a pleasing look. Accuracy and attractiveness are not the same target, which is why narrative work often profiles first and then grades away from it deliberately.
Looking after the chart
The patches are pigment and they fade, particularly with UV exposure. A chart kept face-out in a car window for two summers is no longer a reference. Keep it closed and out of sunlight, never touch the patches, clean only with a dry blower, and replace it every few years if you rely on it for accuracy. A worn chart is worse than no chart, because it produces a confident wrong answer.
When you do not need one
Single camera, raw, one lighting setup, and a look you are going to build by eye anyway: the chart adds little. The case for it strengthens sharply with every additional camera, every change of location, and every requirement that colour be correct rather than pleasing.
Related reading
The colour science behind the correction is in White Balance and Color Tint and Color Temperature and the Kelvin Scale. For measuring accuracy see Delta E Explained, for pipeline-level matching The ACES Workflow, and for judging it on set, Waveforms, Vectorscopes and False Color.